Basic Types of Dimensioning Used in Engineering Drawings
By Kelly Curran, Glenn Sokolowski
Learners examine the basic types of dimensioning including unidirectional and aligned systems, and linear, aligned, angled, arrowless, chain, datum, chart, tabular, radius, diameter, typical, and reference dimensions.
Indirect Measurement Instruments
By Kelly Curran
The learner will define indirect measurement, identify common indirect measuring tools, and select the proper measuring tool for the situation.
Orthographic Projection #1
By Glenn Sokolowski
In this interactive and animated object, learners examine orthographic projection and the Glass Box Theory. Front, side, and top view development is demonstrated with pictorial views of each object to help develop 2D to 3D visualization skills.
The Dial Caliper
By Barbara Anderegg
Learners review guidelines for the proper use of a dial caliper. Illustrations appear throughout the learning object.
How to Read a Caliper
In this interactive object, learners review how to read a caliper. They then test their skills with eight practice questions.
Basic Elements of Dimensions Used in Engineering Drawings
In this interactive object, students explore the basic elements and common terms associated with dimensions and leaders. A quiz completes the activity.
Basic Symbols Used in Engineering Drawings
Learners examine the drawing symbols used for counterbore, countersink, spotface, radius, diameter, and depth. In the quiz that completes the activity, they associate these symbols with machining applications.
In this learning activity you'll examine how a sine bar is used to measure angles.
Reading Vernier Height Gage Quiz
Students take a 13-question quiz to practice reading 25- and 50-division Vernier height gages.
Analyze a Part Drawing
In this interactive object, learners answer 25 questions regarding part or assembly drawings. The basic areas of blueprint reading are covered.
Basic Types of Lines Used in Engineering Drawings
In this highly interactive object, learners associate basic line types and terms with engineering drawing geometry. A quiz completes the activity.
Cutting Tapers Using the Tailstock Offset Method
In this video, you’ll explore how to calculate, setup, and cut a taper using the tailstock offset method.
GD&T: Geometric Characteristic Symbols
In this interactive object, learners test their knowledge of 14 geometric tolerance control symbols.
Brain Exercise: Visualization #3
Learners develop 3D visualization skills by examining front, side, and top orthographic views of objects. Using this information, students select the corresponding isometric view of each object.
Print Reading: An Alphabet of Lines in Print Reading
In this animated activity, learners read about the types of lines found on blueprints. A quiz completes the activity.
Reading a Micrometer
By Sue Silverstein
In this learning activity you'll practice reading a micrometer.
Determining Punch & Dies for Press Brake Forming
By Dave Hoffman
Introduction to selecting the proper punch and die for air bending or bottoming when forming on a press brake. Includes charts and methods for selection.
Using a Depth Micrometer
By Terry Fleischman
Learners will test their ability to read a depth micrometer in this interactive quiz.
Brain Exercise: Visualization #1
In this interactive object, learners practice their 3D visualization skills by identifying the correct isometric view of an object. Front, side, and top orthographic views are shown.
Using a Sine Bar
By Janet Braun
The learner will use the deceptively simple sine bar to measure angles to minutes or even half minutes.
Title Block Tolerances
Learners examine the use of the tolerances displayed in a title block by calculating the minimum and maximum allowable size of a fabricated part. In a brief quiz, students determine whether a part is usable or should be scrapped.
Engine Lathe: Basic Components and Operation
In this video, you’ll explore the engine lathe, its basic components, and you’ll learn to operate its machine controls.
Learners examine pictorial drawings used in engineering including sectioned and exploded drawings. A sketching quiz is provided to help the learner create simple pictorial sketches by using orthographic views and an isometric template.
Brain Exercise: Visualization #2
In this interactive object, learners practice their 3D visualization skills by identifying the correct isometric view of an object.
In this interactive object, learners examine sectional views used in engineering drawings. The sections shown are full, half, offset, aligned, revolved, and broken-out. Learners match drawings of sectional views with the names of the views.